Grundfos UNILIFT AP12.40.06.A1 Stainless Steel Submersible Drainage Pump

UNILIFT AP12 Series | Product No. 96404180 | Single-model focus
Source: Grundfos UNILIFT AP12.40.06.A1 Product Datasheet (Product No. 96404180)

At a Glance: What Is UNILIFT AP12.40.06.A1

Key facts: The Grundfos UNILIFT AP12.40.06.A1 (Product No. 96404180) is a vertical single-stage stainless steel submersible drainage pump of the UNILIFT AP12 series. Maximum flow 5 l/s, maximum head 13 m, rated power P2 0.6 kW, power input P1 0.9 kW. The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304), the connection is 1 1/2 inch, and a level switch (A) is fitted for automatic start and stop. Enclosure class is IP68. All parameters are taken verbatim from the official Grundfos product datasheet, with no fabrication or calculated values.
Maximum flow
5 l/s
Maximum head
13 m
Rated power P2
0.6 kW
Connection
1 1/2 inch
Pump material
Stainless 304
Enclosure
IP68

Product Type and Construction

Submersible drainage pump type. Vertical single-stage stainless steel submersible pump with vertical discharge port and integrated submersible 1-phase totally enclosed motor in insulation class F with thermal overload protection. The pump is fitted with suction strainer and level switch for automatic start and stop. The impeller is a SEMI OPEN impeller for 12 mm free passage suitable for pumping groundwater, surface water, rain water and similar. The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings. The pump is ready for use as it is fitted with carrying handle and is supplied with a 10 m mains cable. The mains cable is of the plug type with glass sealing compound in the socket to prevent penetration of humidity into the stator windings.

Four Models in This Batch - Key Parameter Comparison (per official datasheets)

The UNILIFT AP12 series comprises vertical single-stage stainless steel submersible drainage pumps. Across the four datasheets in this batch, 40.04 / 40.06 / 40.08 / 50.11 correspond to rated power P2 of 0.4 / 0.6 / 0.8 / 1.1 kW respectively; the A1 suffix corresponds to level switch A (automatic start/stop) and single-phase supply 1 x 230 V. Flow, head, current, capacitor and connection size differ between models: AP12.50.11.A1 uses an Rp 2 inch connection, while the other three use Rp 1 1/2 inch. Check each model carefully when selecting.

Key Specifications (Product No. 96404180)

ItemUNILIFT AP12.40.06.A1
Product nameUNILIFT AP12.40.06.A1
Product No.96404180
EAN number5700390910228
Maximum flow5 l/s
Maximum head13 m
Type of impellerSEMI OPEN
Max. particle12 mm
Pump housingStainless steel (EN 1.4301 / AISI 304)
ImpellerStainless steel (EN 1.4301 / AISI 304)
Cable unionBrass (CW602N / C35330)
Type / size of connectionRp / 1 1/2 inch
Maximum installation depth7 m
Inst. dry/wetD/S
InstallationH/V
Place of installationIndoor/outdoor
Range of ambient temperature0..55 °C
Liquid temperature range0..55 °C
Selected liquid temperature20 °C
Density998.2 kg/m3
Power input P10.9 kW
Motor type, 1-phasePSC
Rated power - P20.6 kW
Mains frequency50 Hz
Rated voltage1 x 230 V
Rated current4.4 A
Cos phi - power factor0.99
Rated speed2785 rpm
Capacitor size - run16 μF / 400 V
Enclosure class (IEC 34-5)IP68
Insulation class (IEC 85)F
Built-in motor protection / thermal protectionCONTACT / internal
Length of power cable / cable plug10 m / NONE
Level switchA
Net weight / gross weight12.2 kg / 12.4 kg
Country of originHU
Custom tariff no.84137099.90
Environmental approvalsWEEE
ApprovalsCE, VDE, LGABG, EAC, TUVRHWID, MORO, UKCA, CNROHSEXP, SEPRO

Note: The table lists only items explicitly given in the official Grundfos product datasheet. Fields not stated in the datasheet are omitted; nothing is fabricated or calculated.

Key Features and Benefits

1. All-stainless-steel pump body for corrosion resistance and submersion

The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304) and the cable union is brass (CW602N / C35330), suitable for long-term submerged duty with surface water, groundwater and rain water.

2. Semi-open impeller with 12 mm free passage

The impeller is SEMI OPEN with 12 mm free passage, suitable for pumping groundwater, surface water and similar liquids.

3. Level switch for automatic start and stop

Fitted with a suction strainer and a level switch (A) for automatic start and stop, suitable for unattended drainage and sump applications.

4. IP68 for full submersion, indoor and outdoor use

Enclosure class IP68, maximum installation depth 7 m, suitable for indoor and outdoor installation. A cooling jacket provides continuous cooling of the motor by the pumped liquid, and long-life deep-groove greased-for-life ball bearings are used.

5. Double shaft seal and non-toxic oil chamber

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. A carrying handle is fitted and a 10 m mains cable is supplied; glass sealing compound in the socket prevents penetration of humidity into the stator windings.

Applications and Selection Notes

  • Sump and standing-water drainage: basements, garages, elevator shafts, building sumps and rainwater collection systems.
  • Surface and groundwater pumping: yards, surface water, shallow groundwater and similar liquids, plus temporary construction-site drainage.
  • Lightly particle-laden water: 12 mm free passage suits rain water, surface water and similar liquids containing small particles.
  • Selection note: The four models in this batch differ in flow (maximum 3.89 ... 8.33 l/s) and head (maximum 10 ... 17 m), and in connection size (Rp 1 1/2 vs Rp 2). Refer to the specification table above and match the actual duty and installation conditions.

Frequently Asked Questions

Q1: What type of pump is the UNILIFT AP12?
A: The UNILIFT AP12 is a vertical single-stage stainless steel submersible drainage pump from Grundfos, with a vertical discharge port and an integrated submersible single-phase totally enclosed motor (insulation class F, with thermal overload protection). Enclosure class IP68 allows full submersion; the pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304), suitable for pumping surface water, groundwater, rain water and similar liquids.
Q2: How do the four models (40.04 / 40.06 / 40.08 / 50.11) differ?
A: Rated power P2 is 0.4 / 0.6 / 0.8 / 1.1 kW respectively, maximum flow is 3.89 / 5 / 5.83 / 8.33 l/s, and maximum head is 10 / 13 / 15 / 17 m. For connections, AP12.50.11.A1 uses Rp 2 inch while the other three use Rp 1 1/2 inch. Current, capacitor, weight and customs tariff number also differ; refer to the datasheet for the specific model.
Q3: What are the liquid and ambient temperature ranges and the maximum installation depth?
A: For all four models the liquid temperature range and ambient temperature range are both 0..55 °C, with selected liquid temperature 20 °C and density 998.2 kg/m3. Maximum installation depth is 7 m; indoor and outdoor installation is permitted, and the motor is continuously cooled by the pumped liquid.
Q4: What should be noted regarding electrical supply and wiring?
A: All four models are single-phase 1 x 230 V / 50 Hz, motor type PSC, with built-in contact motor protection and internal thermal protection, and run capacitors (this model: 16 μF / 400 V). Enclosure class is IP68. A 10 m mains cable is supplied but no plug is fitted (NONE); wiring must be carried out by a qualified person in accordance with regulations.
Q5: Which liquids is this pump suitable for?
A: The datasheet states the pump is suitable for pumping groundwater, surface water and similar liquids, and the impeller allows 12 mm free passage. When selecting, check the particle content and corrosiveness of the actual liquid, and verify power, head and connection size.
Source statement: The technical parameters and product information in this article are taken from the official Grundfos product datasheet for UNILIFT AP12.40.06.A1 (Product No. 96404180). Parameters (flow, head, power, materials, connection, electrical data, approvals, etc.) follow that official datasheet. For final selection, installation and purchasing, always refer to the latest official Grundfos technical documentation and the actual operating conditions.

需要选型或采购「格兰富」水泵?欢迎联系

电话 15655120770
或邮件:pengry@qq.com(工作日快速回复)