Grundfos UNILIFT AP12.40.08.A3 Stainless Steel Submersible Drainage Pump

UNILIFT AP12 A3 Three-phase Series | Product No. 96010925 | Single-model focus
Source: Grundfos UNILIFT AP12.40.08.A3 Product Datasheet (Product No. 96010925)

At a Glance: What Is UNILIFT AP12.40.08.A3

Key facts: The Grundfos UNILIFT AP12.40.08.A3 (Product No. 96010925) is a vertical single-stage three-phase stainless steel submersible drainage pump of the UNILIFT AP12 A3 series. Maximum flow 5.83 l/s, maximum head 15 m, rated power P2 0.8 kW, power input P1 1.2 kW. It is a 3 x 400 V model supplied with a control box (including motor starter and motor protection) and a level switch with 10 m cable; the pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304), the connection is 1 1/2 inch, and enclosure class is IP68. All parameters are taken verbatim from the official Grundfos product datasheet, with no fabrication or calculated values.
Maximum flow
5.83 l/s
Maximum head
15 m
Rated power P2
0.8 kW
Power supply
3 x 400 V
Connection
1 1/2 inch
Enclosure
IP68

Product Type and Construction

Submersible drainage pump type. Vertical single-stage stainless steel submersible pump with vertical discharge port and integrated submersible 3-phase totally enclosed motor in insulation class F. The pump is fitted with a suction strainer. The pump is supplied with a control box including motor starter, a motor protection and a float switch for automatic start/stop of the pump. The float switch contains 10 m cable. And there is a 0.8 m mains cable connected to the box (see electrical data for optional CEE plug). The impeller is a SEMI OPEN impeller for 12 mm free passage suitable for pumping groundwater, surface water, rain water and similar liquids. The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings. The pump is ready for use as it is fitted with carrying handle and is supplied with a 10 m mains cable. The mains cable is of the plug type with glass sealing compound in the socket to prevent penetration of humidity into the stator windings.

A3 (three-phase) vs A1 (single-phase); Four Models in This Batch

The A3 suffix denotes a three-phase 3 x 400 V version, supplied with a control box (containing motor starter and motor protection, plus a 0.8 m cable) and a level switch with its own 10 m cable for automatic start and stop. Built-in motor protection is NONE and thermal protection is external (provided by the control box); no run capacitor is listed in the datasheet. Do not confuse it with the A1 single-phase version. Across the four datasheets in this batch, 40.04 / 40.06 / 40.08 / 50.11 correspond to rated power P2 of 0.4 / 0.6 / 0.8 / 1.2 kW; the AP12.50.11.A3 has a maximum flow of 8.89 l/s, maximum head of 18 m and an Rp 2 inch connection, while the other three use Rp 1 1/2 inch.

Key Specifications (Product No. 96010925)

ItemUNILIFT AP12.40.08.A3
Product nameUNILIFT AP12.40.08.A3
Product No.96010925
EAN number5700390901011
Maximum flow5.83 l/s
Maximum head15 m
Type of impellerSEMI OPEN
Max. particle12 mm
Pump housingStainless steel (EN 1.4301 / AISI 304)
ImpellerStainless steel (EN 1.4301 / AISI 304)
Cable unionBrass (CW602N / C35330)
Type / size of connectionRp / 1 1/2 inch
Maximum installation depth7 m
Inst. dry/wetD/S
InstallationH/V
Place of installationIndoor/outdoor
Range of ambient temperature0..55 °C
Liquid temperature range0..55 °C
Selected liquid temperature20 °C
Density998.2 kg/m3
Power input P11.2 kW
Rated power - P20.8 kW
Mains frequency50 Hz
Rated voltage3 x 400 V (three-phase)
Rated current2.1 A
Cos phi - power factor0.87
Rated speed2810 rpm
Capacitor size - runNo run capacitor listed in datasheet (three-phase)
Enclosure class (IEC 34-5)IP68
Insulation class (IEC 85)F
Built-in motor protection / thermal protectionNONE / external
Length of power cable / cable plug10 m / NONE
Level switchA (with control box and float switch)
Net weight / gross weight14.5 kg / 16 kg
Danish VVS No.391314331
Swedish RSK No.5880112
Finnish LVI No.4822578
Country of originHU
Custom tariff no.84137091.90
Environmental approvalsWEEE
ApprovalsCE, LGABG, EAC, TUVRHWID, MORO, UKCA, CNROHSEXP, SEPRO

Note: The table lists only items explicitly given in the official Grundfos product datasheet. Fields not stated in the datasheet are omitted; nothing is fabricated or calculated.

Key Features and Benefits

1. Three-phase motor with control box supplied

The A3 version integrates a submersible three-phase totally enclosed motor (insulation class F) and is supplied with a control box containing the motor starter and motor protection plus a 0.8 m cable, together with a level switch (10 m cable) for automatic start and stop - a complete package for three-phase installations.

2. All-stainless-steel pump body

The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304) and the cable union is brass (CW602N / C35330), suitable for long-term submerged duty with surface water, groundwater and rain water.

3. Semi-open impeller with 12 mm free passage

The impeller is SEMI OPEN with 12 mm free passage, suitable for pumping groundwater, surface water, rain water and similar liquids.

4. IP68 for full submersion, indoor and outdoor use

Enclosure class IP68, maximum installation depth 7 m, suitable for indoor and outdoor installation. A cooling jacket provides continuous cooling of the motor by the pumped liquid, and long-life deep-groove greased-for-life ball bearings are used.

5. Double shaft seal and non-toxic oil chamber

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. A carrying handle is fitted and a 10 m mains cable is supplied; glass sealing compound in the socket prevents penetration of humidity into the stator windings.

Applications and Selection Notes

  • Sump and standing-water drainage: basements, garages, elevator shafts, building sumps and rainwater collection systems.
  • Surface and groundwater pumping: yards, surface water, shallow groundwater and similar liquids, plus temporary construction-site drainage.
  • Lightly particle-laden water: 12 mm free passage suits rain water, surface water and similar liquids containing small particles.
  • Selection note: The four models differ in flow (maximum 3.89 ... 8.89 l/s) and head (maximum 10 ... 18 m), and in connection size (Rp 1 1/2 vs Rp 2). A3 is a three-phase 3 x 400 V package; confirm a three-phase supply on site and match the actual duty to the specification table above.

Frequently Asked Questions

Q1: What type of pump is the UNILIFT AP12 A3?
A: The UNILIFT AP12 A3 is a vertical single-stage three-phase stainless steel submersible drainage pump from Grundfos, with a vertical discharge port and an integrated submersible three-phase totally enclosed motor (insulation class F). Enclosure class IP68 allows full submersion; the pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304), and it is supplied with a control box and level switch, suitable for pumping surface water, groundwater, rain water and similar liquids.
Q2: How does the three-phase A3 differ from the single-phase A1?
A: A3 is three-phase 3 x 400 V, with built-in motor protection NONE and thermal protection external (provided by the supplied control box); it comes with a control box (motor starter and protection, 0.8 m cable) and a level switch with a 10 m cable. No run capacitor is listed in the datasheet. The A1 is single-phase 1 x 230 V with a PSC motor, a run capacitor and built-in contact protection. For example, the A1 version of AP12.50.11 is 8.33 l/s / 17 m / P2 1.1 kW, while the A3 version is 8.89 l/s / 18 m / P2 1.2 kW; the two are not interchangeable.
Q3: How do the four models (40.04 / 40.06 / 40.08 / 50.11) differ?
A: Rated power P2 is 0.4 / 0.6 / 0.8 / 1.2 kW respectively, maximum flow is 3.89 / 5 / 5.83 / 8.89 l/s, and maximum head is 10 / 13 / 15 / 18 m. For connections, AP12.50.11.A3 uses Rp 2 inch while the other three use Rp 1 1/2 inch. Current, power factor, weight, Nordic numbers and customs tariff number also differ; refer to the datasheet for the specific model.
Q4: What are the liquid and ambient temperature ranges and installation depth?
A: For all four models the liquid temperature range and ambient temperature range are both 0..55 °C, with selected liquid temperature 20 °C and density 998.2 kg/m3. Maximum installation depth is 7 m; indoor and outdoor installation is permitted, and the motor is continuously cooled by the pumped liquid.
Q5: What should be noted regarding electrical installation?
A: All four models are three-phase 3 x 400 V / 50 Hz, with built-in motor protection NONE and thermal protection external, with protection provided by the supplied control box. The pump has a 10 m mains cable but no plug (NONE), and the control box has a separate 0.8 m cable. Wiring must be carried out by a qualified person, and a three-phase supply must be available on site.
Source statement: The technical parameters and product information in this article are taken from the official Grundfos product datasheet for UNILIFT AP12.40.08.A3 (Product No. 96010925). Parameters (flow, head, power, materials, connection, electrical data, approvals, etc.) follow that official datasheet. For final selection, installation and purchasing, always refer to the latest official Grundfos technical documentation and the actual operating conditions.

需要选型或采购「格兰富」水泵?欢迎联系

电话 15655120770
或邮件:pengry@qq.com(工作日快速回复)