Grundfos UNILIFT AP35B.50.06.A1V Stainless Steel Submersible Effluent Pump

UNILIFT AP35B Series | Product No. 92532137 | Single-model focus
Source: Grundfos UNILIFT AP35B.50.06.A1V Product Datasheet (Product No. 92532137)

At a Glance: What Is UNILIFT AP35B.50.06.A1V

Key facts: The Grundfos UNILIFT AP35B.50.06.A1V (Product No. 92532137) is a vertical single-stage stainless steel submersible effluent pump of the UNILIFT AP35B series. Maximum flow 5 l/s, maximum head 11 m, rated power P2 0.66 kW. It uses a VORTEX impeller with 35 mm free passage, an Rp 2 inch connection, single-phase 1 x 230 V supply, a liquid temperature range of 0..40 °C and enclosure class IP68, with a level switch for automatic start and stop. The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304). All parameters are taken verbatim from the official Grundfos product datasheet, with no fabrication or calculated values.
Maximum flow
5 l/s
Maximum head
11 m
Rated power P2
0.66 kW
Free passage
35 mm
Connection
Rp 2 inch
Enclosure
IP68

Product Type and Construction

Submersible effluent pump. Vertical single-stage stainless steel submersible pump with integrated submersible 1-phase motor. The pump is fitted with ring stand and carrying handle and is supplied with a 10 m mains cable and a level switch for automatic start and stop. The impeller is a VORTEX impeller for 35 mm free passage suitable for pumping surface water, groundwater, wastewater and similar. The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. The motor is insulation class F with thermal overload protection and has long-life deep-groove greased-for-life ball bearings. The pump has an Rp 2 inch discharge port and is ready for installation either free-standing or on an auto-coupling system.

UNILIFT B Series Features and the Four Models in This Batch

The UNILIFT B series (AP35B / AP50B) comprises stainless steel submersible effluent pumps fitted with a ring stand and carrying handle, installable free-standing or on an auto-coupling system, using a VORTEX impeller (the Chinese datasheet uses varying terms such as "漩涡" and "滋润"; this article follows the VORTEX description). Compared with the non-B AP35/AP50, the B series has a liquid and ambient temperature range of 0..40 °C, a uniform Rp 2 inch connection, and is explicitly suitable for pumping wastewater. The four models in this batch - AP35B.50.06, AP35B.50.08, AP50B.50.08 and AP50B.50.11 - have rated power P2 of 0.66 / 0.71 / 0.74 / 1.21 kW, maximum flow of 5 / 5.83 / 6.67 / 7.78 l/s and maximum head of 11 / 13 / 11 / 14 m, with free passage of 35 mm for AP35B and 50 mm for AP50B. Country of origin and approvals differ between models; check each parameter carefully when selecting.

Key Specifications (Product No. 92532137)

ItemUNILIFT AP35B.50.06.A1V
Product nameUNILIFT AP35B.50.06.A1V
Product No.92532137
EAN number5715115835885
Maximum flow5 l/s
Maximum head11 m
Type of impellerVORTEX
Max. particle35 mm
Pump housingStainless steel (EN 1.4301 / AISI 304)
ImpellerStainless steel (EN 1.4301 / AISI 304)
Type / size of connectionRp / 2 inch
Maximum installation depth7 m
Inst. dry/wetS
InstallationH/V
Auto-couplingY
Place of installationIndoor/outdoor
Range of ambient temperature0..40 °C
Liquid temperature range0..40 °C
Selected liquid temperature20 °C
Density998.2 kg/m3
Power input P11 kW
Motor type, 1-phasePSC
Rated power - P20.66 kW
Mains frequency50 Hz
Rated voltage1 x 230 V
Rated current4.6 A
Cos phi - power factor0.98
Rated speed2810 rpm
Capacitor size - run16 μF / 400 V
Enclosure class (IEC 34-5)IP68
Insulation class (IEC 85)F
Built-in motor protection / thermal protectionCONTACT / internal
Length of power cable / cable plug10 m / NONE
Level switchA
Net weight / gross weight9.9 kg / 10.5 kg
Sales regionChina
Country of originHU
Custom tariff no.84139100.00
Environmental approvalsWEEE
ApprovalsCE, VDE, LGABG, EAC, TUVRHWID, MORO, UKCA, CNROHSEXP, SEPRO

Note: The table lists only items explicitly given in the official Grundfos product datasheet. Fields not stated in the datasheet are omitted; nothing is fabricated or calculated.

Key Features and Benefits

1. Effluent pump design for wastewater applications

Designed as a submersible effluent pump with a ring stand and carrying handle, installable free-standing or on an auto-coupling system. The VORTEX impeller allows 35 mm free passage (35 mm for AP35B, 50 mm for AP50B), suitable for pumping surface water, groundwater, wastewater and similar liquids.

2. All-stainless-steel pump body

The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304), suitable for long-term submerged duty with wastewater.

3. Level switch for automatic start and stop

Supplied with a 10 m mains cable and a level switch (A) for automatic start and stop, suitable for unattended drainage and sump applications.

4. IP68 for full submersion, indoor and outdoor use

Enclosure class IP68, maximum installation depth 7 m, suitable for indoor and outdoor installation, with long-life deep-groove greased-for-life ball bearings.

5. Double shaft seal and non-toxic oil chamber

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. The motor is insulation class F with thermal overload protection, and a carrying handle is fitted for easy movement and installation.

Applications and Selection Notes

  • Wastewater and surface water pumping: the datasheet states the pump is suitable for pumping surface water, groundwater, wastewater and similar liquids, for sumps and building drainage.
  • Liquids with larger particles: the VORTEX impeller allows 35 mm free passage (35 mm for AP35B, 50 mm for AP50B), suitable for similar liquids containing small to relatively large particles.
  • Flexible installation: fitted with a ring stand and carrying handle, installable free-standing or via the auto-coupling system (Y), indoors or outdoors.
  • Selection note: The four models differ in flow (maximum 5 ... 7.78 l/s), head (maximum 11 ... 14 m), country of origin, customs tariff number and approvals. Refer to the specification table above and match the actual duty and installation conditions.

Frequently Asked Questions

Q1: What type of pump is the UNILIFT AP35B?
A: The UNILIFT AP35B is a vertical single-stage stainless steel submersible effluent pump from Grundfos, with an integrated submersible single-phase totally enclosed motor. Enclosure class IP68 allows full submersion; the pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304), it uses a VORTEX impeller and is fitted with a ring stand, carrying handle and level switch, suitable for pumping surface water, groundwater, wastewater and similar liquids.
Q2: How do AP35B and AP50B differ, and how do the four models compare?
A: The main differences are free passage and performance: AP35B has 35 mm free passage and AP50B has 50 mm, and all four models use an Rp 2 inch connection. Rated power P2 is 0.66 / 0.71 / 0.74 / 1.21 kW, maximum flow is 5 / 5.83 / 6.67 / 7.78 l/s and maximum head is 11 / 13 / 11 / 14 m respectively; country of origin, customs tariff number and approvals also differ. Refer to the datasheet for the specific model.
Q3: How does the B series differ from the non-B AP35/AP50?
A: AP35B/AP50B are submersible effluent pumps with a ring stand and carrying handle, and the pumped medium explicitly includes wastewater. The liquid and ambient temperature range is 0..40 °C, the connection is uniformly Rp 2 inch and an auto-coupling system (Y) is available. The non-B AP35/AP50 have a liquid/ambient temperature range of 0..55 °C and the AP35 uses a 1 1/2 inch connection. Parameters differ, so select by the exact model.
Q4: What are the liquid and ambient temperature ranges and installation depth?
A: For all four models the liquid temperature range and ambient temperature range are both 0..40 °C, with selected liquid temperature 20 °C and density 998.2 kg/m3. Maximum installation depth is 7 m; indoor and outdoor installation is permitted, free-standing or with the auto-coupling system (Y).
Q5: What should be noted regarding electrical supply and wiring?
A: All four models are single-phase 1 x 230 V / 50 Hz, motor type PSC, with built-in contact motor protection and internal thermal protection, and run capacitors (this model: 16 μF / 400 V). Enclosure class is IP68. A 10 m mains cable is supplied but no plug is fitted (NONE); wiring must be carried out by a qualified person in accordance with regulations.
Source statement: The technical parameters and product information in this article are taken from the official Grundfos product datasheet for UNILIFT AP35B.50.06.A1V (Product No. 92532137). Parameters (flow, head, power, materials, impeller type, free passage, connection, electrical data, approvals, etc.) follow that official datasheet. For final selection, installation and purchasing, always refer to the latest official Grundfos technical documentation and the actual operating conditions.

需要选型或采购「格兰富」水泵?欢迎联系

电话 15655120770
或邮件:pengry@qq.com(工作日快速回复)