Grundfos UNILIFT AP50.50.08.A1V Stainless Steel Submersible Drainage Pump

UNILIFT AP50 Series | Product No. 96404185 | Single-model focus
Source: Grundfos UNILIFT AP50.50.08.A1V Product Datasheet (Product No. 96404185)

At a Glance: What Is UNILIFT AP50.50.08.A1V

Key facts: The Grundfos UNILIFT AP50.50.08.A1V (Product No. 96404185) is a vertical single-stage stainless steel submersible drainage pump of the UNILIFT AP50 series. Maximum flow 6.94 l/s, maximum head 9 m, rated power P2 0.8 kW. It uses a VORTEX impeller with 50 mm free passage, a 2 inch connection, single-phase 1 x 230 V supply and enclosure class IP68, with a level switch for automatic start and stop. The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304). All parameters are taken verbatim from the official Grundfos product datasheet, with no fabrication or calculated values.
Maximum flow
6.94 l/s
Maximum head
9 m
Rated power P2
0.8 kW
Free passage
50 mm
Connection
2 inch
Enclosure
IP68

Product Type and Construction

Submersible drainage pump type. Vertical single-stage stainless steel submersible pump with vertical discharge port and integrated submersible 1-phase totally enclosed motor in insulation class F with thermal overload protection. The pump is fitted with suction strainer and level switch for automatic start and stop. The impeller is a VORTEX impeller for 50 mm free passage suitable for pumping groundwater, surface water, rain water and similar. The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings. The pump is ready for use as it is fitted with carrying handle and is supplied with a 10 m mains cable. The mains cable is of the plug type with glass sealing compound in the socket to prevent penetration of humidity into the stator windings.

UNILIFT AP50 Features and the Four Models in This Batch

UNILIFT AP50 is a range of stainless steel submersible drainage pumps using a VORTEX impeller with free passage of 35 mm (AP35) or 50 mm (AP50), considerably higher than the 12 mm semi-open impeller of the UNILIFT AP12 series. The four models in this batch - AP35.40.06, AP35.40.08, AP50.50.08 and AP50.50.11 - have rated power P2 of 0.6 / 0.7 / 0.8 / 1.1 kW; AP35 models use a 1 1/2 inch connection and AP50 models an Rp 2 inch connection. All are single-phase 1 x 230 V with PSC motors; flow, head, current, capacitor and weight differ between models, so check each parameter carefully when selecting.

Key Specifications (Product No. 96404185)

ItemUNILIFT AP50.50.08.A1V
Product nameUNILIFT AP50.50.08.A1V
Product No.96404185
EAN number5700390910419
Maximum flow6.94 l/s
Maximum head9 m
Type of impellerVORTEX
Max. particle50 mm
Pump housingStainless steel (EN 1.4301 / AISI 304)
ImpellerStainless steel (EN 1.4301 / AISI 304)
Cable unionBrass (CW602N / C35330)
Type / size of connectionRp / 2 inch
Maximum installation depth7 m
Inst. dry/wetD/S
InstallationH/V
Place of installationIndoor/outdoor
Range of ambient temperature0..55 °C
Liquid temperature range0..55 °C
Selected liquid temperature20 °C
Density998.2 kg/m3
Power input P11.3 kW
Motor type, 1-phasePSC
Rated power - P20.8 kW
Mains frequency50 Hz
Rated voltage1 x 230 V
Rated current5.9 A
Cos phi - power factor0.99
Rated speed2790 rpm
Capacitor size - run16 μF / 400 V
Enclosure class (IEC 34-5)IP68
Insulation class (IEC 85)F
Built-in motor protection / thermal protectionCONTACT / internal
Length of power cable / cable plug10 m / NONE
Level switchA
Net weight / gross weight16.3 kg / 17.4 kg
Country of originHU
Custom tariff no.84137099.90
Environmental approvalsWEEE
ApprovalsCE, VDE, LGABG, EAC, TUVRHWID, MORO, UKCA, CNROHSEXP, SEPRO

Note: The table lists only items explicitly given in the official Grundfos product datasheet. Fields not stated in the datasheet are omitted; nothing is fabricated or calculated.

Key Features and Benefits

1. VORTEX impeller with large free passage

The VORTEX impeller allows 50 mm free passage (35 mm for AP35, 50 mm for AP50), suitable for pumping surface water, groundwater and similar liquids containing relatively large particles, with low clogging risk.

2. All-stainless-steel pump body

The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304) and the cable union is brass (CW602N / C35330), suitable for long-term submerged duty.

3. Level switch for automatic start and stop

Fitted with a suction strainer and a level switch (A) for automatic start and stop, suitable for unattended drainage and sump applications.

4. IP68 for full submersion, indoor and outdoor use

Enclosure class IP68, maximum installation depth 7 m, suitable for indoor and outdoor installation. A cooling jacket provides continuous cooling of the motor by the pumped liquid, and long-life deep-groove greased-for-life ball bearings are used.

5. Double shaft seal and non-toxic oil chamber

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. A carrying handle is fitted and a 10 m mains cable is supplied; glass sealing compound in the socket prevents penetration of humidity into the stator windings.

Applications and Selection Notes

  • Surface and groundwater pumping: the datasheet states the pump is suitable for pumping surface water, groundwater and similar liquids, for yards, sumps and rainwater collection systems.
  • Liquids with larger particles: the VORTEX impeller allows 50 mm free passage, suitable for similar liquids containing small to relatively large particles.
  • Standing-water drainage: basements, garages, elevator shafts and temporary construction-site drainage.
  • Selection note: The four models differ in flow (maximum 4.17 ... 8.33 l/s), head (maximum 9 ... 12 m), connection size and free passage. Refer to the specification table above and match the actual duty and installation conditions.

Frequently Asked Questions

Q1: What type of pump is the UNILIFT AP50?
A: The UNILIFT AP50 is a vertical single-stage stainless steel submersible drainage pump from Grundfos, with a vertical discharge port and an integrated submersible single-phase totally enclosed motor (insulation class F, with thermal overload protection). Enclosure class IP68 allows full submersion; the pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304) and it uses a VORTEX impeller, suitable for pumping surface water, groundwater and similar liquids.
Q2: How do AP35 and AP50 differ, and how do the four models compare?
A: The main differences are free passage and connection: AP35 has 35 mm free passage and a 1 1/2 inch connection; AP50 has 50 mm free passage and an Rp 2 inch connection. The four models have rated power P2 of 0.6 / 0.7 / 0.8 / 1.1 kW, maximum flow of 4.17 / 5 / 6.94 / 8.33 l/s and maximum head of 10 / 11 / 9 / 12 m respectively; current, capacitor and weight also differ. Refer to the datasheet for the specific model.
Q3: How does this series differ from the UNILIFT AP12?
A: The AP12 uses a semi-open impeller with 12 mm free passage, whereas AP35/AP50 use a VORTEX impeller with 35 / 50 mm free passage, giving greater solids-handling capability; the connections, power range and flow/head also differ. Note that the Chinese datasheet renders the AP35/AP50 impeller term literally as "滋润叶轮", while the English datasheet states VORTEX; this article follows the VORTEX impeller description.
Q4: What are the liquid and ambient temperature ranges and installation depth?
A: For all four models the liquid temperature range and ambient temperature range are both 0..55 °C, with selected liquid temperature 20 °C and density 998.2 kg/m3. Maximum installation depth is 7 m; indoor and outdoor installation is permitted, and the motor is continuously cooled by the pumped liquid.
Q5: What should be noted regarding electrical supply and wiring?
A: All four models are single-phase 1 x 230 V / 50 Hz, motor type PSC, with built-in contact motor protection and internal thermal protection, and run capacitors (this model: 16 μF / 400 V). Enclosure class is IP68. A 10 m mains cable is supplied but no plug is fitted (NONE); wiring must be carried out by a qualified person in accordance with regulations.
Source statement: The technical parameters and product information in this article are taken from the official Grundfos product datasheet for UNILIFT AP50.50.08.A1V (Product No. 96404185). Parameters (flow, head, power, materials, impeller type, free passage, connection, electrical data, approvals, etc.) follow that official datasheet. For final selection, installation and purchasing, always refer to the latest official Grundfos technical documentation and the actual operating conditions.

需要选型或采购「格兰富」水泵?欢迎联系

电话 15655120770
或邮件:pengry@qq.com(工作日快速回复)