Grundfos UNILIFT AP50.50.11.A3V Stainless Steel Submersible Drainage Pump

UNILIFT AP50 A3V Three-phase Series | Product No. 96010935 | Single-model focus
Source: Grundfos UNILIFT AP50.50.11.A3V Product Datasheet (Product No. 96010935)

At a Glance: What Is UNILIFT AP50.50.11.A3V

Key facts: The Grundfos UNILIFT AP50.50.11.A3V (Product No. 96010935) is a vertical single-stage three-phase stainless steel submersible drainage pump of the UNILIFT AP50 A3V series. Maximum flow 8.89 l/s, maximum head 13 m, rated power P2 1.2 kW. It is a 3 x 400 V model using a VORTEX impeller with 50 mm free passage and a 2 inch connection, supplied with a control box (motor starter and motor protection) and a level switch with 10 m cable; enclosure class is IP68. The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304). All parameters are taken verbatim from the official Grundfos product datasheet, with no fabrication or calculated values.
Maximum flow
8.89 l/s
Maximum head
13 m
Rated power P2
1.2 kW
Free passage
50 mm
Power supply
3 x 400 V
Enclosure
IP68

Product Type and Construction

Submersible drainage pump type. Vertical single-stage stainless steel submersible pump with vertical discharge port and integrated submersible 3-phase totally enclosed motor in insulation class F. The pump is fitted with a suction strainer. The pump is supplied with a control box including motor starter, a motor protection and a float switch for automatic start/stop of the pump. The float switch contains 10 m cable. And there is a 0.8 m mains cable connected to the box (see electrical data for optional CEE plug). The impeller is a VORTEX impeller for 50 mm free passage suitable for pumping groundwater, surface water, rain water and similar liquids. The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings. The pump is ready for use as it is fitted with carrying handle and is supplied with a 10 m mains cable. The mains cable is of the plug type with glass sealing compound in the socket to prevent penetration of humidity into the stator windings.

A3V (three-phase) vs A1V (single-phase); Four Models in This Batch

The A3V suffix denotes a three-phase 3 x 400 V version, supplied with a control box (containing motor starter and motor protection, plus a 0.8 m cable) and a level switch with its own 10 m cable for automatic start and stop. Built-in motor protection is NONE and thermal protection is external (provided by the control box); no run capacitor is listed in the datasheet. Do not confuse it with the A1V single-phase version. The four models in this batch - AP35.40.06, AP35.40.08, AP50.50.08 and AP50.50.11 - have rated power P2 of 0.6 / 0.7 / 0.8 / 1.2 kW, maximum flow of 4.17 / 5 / 6.94 / 8.89 l/s and maximum head of 10 / 11 / 9 / 13 m. The AP50.50.11.A3V is 8.89 l/s / 13 m / P2 1.2 kW, differing from the A1V version's 8.33 l/s / 12 m / 1.1 kW; the two are not interchangeable. The impeller is VORTEX (the Chinese datasheet uses varying terms such as "漩涡", "滋润" and "潺涡"; this article follows the VORTEX description), with free passage of 35 mm for AP35 and 50 mm for AP50.

Key Specifications (Product No. 96010935)

ItemUNILIFT AP50.50.11.A3V
Product nameUNILIFT AP50.50.11.A3V
Product No.96010935
EAN number5700390901202
Maximum flow8.89 l/s
Maximum head13 m
Type of impellerVORTEX
Max. particle50 mm
Pump housingStainless steel (EN 1.4301 / AISI 304)
ImpellerStainless steel (EN 1.4301 / AISI 304)
Cable unionBrass (CW602N / C35330)
Type / size of connectionRp / 2 inch
Maximum installation depth7 m
Inst. dry/wetD/S
InstallationH/V
Place of installationIndoor/outdoor
Range of ambient temperature0..55 °C
Liquid temperature range0..55 °C
Selected liquid temperature20 °C
Density998.2 kg/m3
Power input P11.9 kW
Rated power - P21.2 kW
Mains frequency50 Hz
Rated voltage3 x 400 V (three-phase)
Rated current3 A
Cos phi - power factor0.88
Rated speed2785 rpm
Capacitor size - runNo run capacitor listed in datasheet (three-phase)
Enclosure class (IEC 34-5)IP68
Insulation class (IEC 85)F
Built-in motor protection / thermal protectionNONE / external
Length of power cable / cable plug10 m / NONE
Level switchA (with control box and float switch)
Net weight / gross weight15.4 kg / 18.5 kg
Danish VVS No.391322332
Swedish RSK No.5880122
Finnish LVI No.数据样本未列
Country of originHU
Custom tariff no.84137091.90
Environmental approvalsWEEE
ApprovalsCE, LGABG, EAC, TUVRHWID, MORO, UKCA, CNROHSEXP, SEPRO

Note: The table lists only items explicitly given in the official Grundfos product datasheet. Fields not stated in the datasheet are marked as "not listed in datasheet"; nothing is fabricated or calculated.

Key Features and Benefits

1. Three-phase motor with control box supplied

The A3V version integrates a submersible three-phase totally enclosed motor (insulation class F) and is supplied with a control box containing the motor starter and motor protection plus a 0.8 m cable, together with a level switch (10 m cable) for automatic start and stop - a complete package for three-phase installations.

2. VORTEX impeller with large free passage

The VORTEX impeller allows 50 mm free passage (35 mm for AP35, 50 mm for AP50), suitable for pumping surface water, groundwater and similar liquids containing relatively large particles, with low clogging risk.

3. All-stainless-steel pump body

The pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304) and the cable union is brass (CW602N / C35330), suitable for long-term submerged duty.

4. IP68 for full submersion, indoor and outdoor use

Enclosure class IP68, maximum installation depth 7 m, suitable for indoor and outdoor installation. A cooling jacket provides continuous cooling of the motor by the pumped liquid, and long-life deep-groove greased-for-life ball bearings are used.

5. Double shaft seal and non-toxic oil chamber

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil. A carrying handle is fitted and a 10 m mains cable is supplied; glass sealing compound in the socket prevents penetration of humidity into the stator windings.

Applications and Selection Notes

  • Surface and groundwater pumping: the datasheet states the pump is suitable for pumping surface water, groundwater and similar liquids, for yards, sumps and rainwater collection systems.
  • Liquids with larger particles: the VORTEX impeller allows 50 mm free passage, suitable for similar liquids containing small to relatively large particles.
  • Standing-water drainage: basements, garages, elevator shafts and temporary construction-site drainage.
  • Selection note: The four models differ in flow (maximum 4.17 ... 8.89 l/s), head (maximum 9 ... 13 m), connection size and free passage. A3V is a three-phase 3 x 400 V package; confirm a three-phase supply on site and match the actual duty to the specification table above.

Frequently Asked Questions

Q1: What type of pump is the UNILIFT AP50 A3V?
A: The UNILIFT AP50 A3V is a vertical single-stage three-phase stainless steel submersible drainage pump from Grundfos, with a vertical discharge port and an integrated submersible three-phase totally enclosed motor (insulation class F). Enclosure class IP68 allows full submersion; the pump housing and impeller are both stainless steel (EN 1.4301 / AISI 304), it uses a VORTEX impeller and is supplied with a control box and level switch, suitable for pumping surface water, groundwater and similar liquids.
Q2: How does the three-phase A3V differ from the single-phase A1V?
A: A3V is three-phase 3 x 400 V, with built-in motor protection NONE and thermal protection external (provided by the supplied control box); it comes with a control box (motor starter and protection, 0.8 m cable) and a level switch with a 10 m cable. No run capacitor is listed in the datasheet. The A1V is single-phase 1 x 230 V with a PSC motor, a run capacitor and built-in contact and internal thermal protection. For AP50.50.11, the A3V version is 8.89 l/s / 13 m / P2 1.2 kW while the A1V version is 8.33 l/s / 12 m / P2 1.1 kW; the two are not interchangeable.
Q3: How do AP35 and AP50 differ, and how do the four models compare?
A: The main differences are free passage and connection: AP35 has 35 mm free passage and a 1 1/2 inch connection; AP50 has 50 mm free passage and an Rp 2 inch connection. The four models have rated power P2 of 0.6 / 0.7 / 0.8 / 1.2 kW, maximum flow of 4.17 / 5 / 6.94 / 8.89 l/s and maximum head of 10 / 11 / 9 / 13 m respectively; current, power factor, Nordic numbers and weight also differ. Refer to the datasheet for the specific model.
Q4: What are the liquid and ambient temperature ranges and installation depth?
A: For all four models the liquid temperature range and ambient temperature range are both 0..55 °C, with selected liquid temperature 20 °C and density 998.2 kg/m3. Maximum installation depth is 7 m; indoor and outdoor installation is permitted, and the motor is continuously cooled by the pumped liquid.
Q5: What should be noted regarding electrical installation?
A: All four models are three-phase 3 x 400 V / 50 Hz, with built-in motor protection NONE and thermal protection external, with protection provided by the supplied control box. The pump has a 10 m mains cable but no plug (NONE), and the control box has a separate 0.8 m cable. Wiring must be carried out by a qualified person, and a three-phase supply must be available on site.
Source statement: The technical parameters and product information in this article are taken from the official Grundfos product datasheet for UNILIFT AP50.50.11.A3V (Product No. 96010935). Parameters (flow, head, power, materials, impeller type, free passage, connection, electrical data, approvals, etc.) follow that official datasheet. For final selection, installation and purchasing, always refer to the latest official Grundfos technical documentation and the actual operating conditions.

需要选型或采购「格兰富」水泵?欢迎联系

电话 15655120770
或邮件:pengry@qq.com(工作日快速回复)